2023 Hans Christian 41T

The hull and deck are hand laid up in accordance with approved laminates and procedures. The standard hull and deck color is off white (ref. LR #8981).In the hull a combination of woven roving and chopped strand mat are used with thickness increasing towards the keel. There is a reinforcing balsa core in the topsides which stops at six inches above the waterline. Vinylester resin is used for the initial layers below the waterline. The ballast keel is encapsulated entirely within the hull molding. The deck molding has a PVC foam and/or balsa core which is replaced with plywood in high stress areas where fittings are attached. A two part epoxy barrier coat paint is applied below the boot-top for extra anti-osmosis protection.

The rudder is molded GRP with a stainless steel stock, the base of which locates onto the bottom rudder skeg. The heel fitting is a cast bronze item. The rudder post is machined to accept cable steering fittings as standard.

The standard rig for the vessel is a cutter rig with a club footed staysail to the dimensions as follows:

I 52' 0" (15.85m)
J 22’6” (6.855m)
P 48'3 ½”(14.72m)
E 15'7" (4.75m)

A single spreader aluminum mast with external halyards for Mainsail, Headsail and Staysail. Three winches and cleats mast mounted for halyards. One masthead light, one bow light and one pair of spreader lights. The aluminum boom fitted with a 4:1outhaul system and two winches and cleats for outhaul and reefing. Standing rigging of 1 x 19stainless steel wire with swage on upper end fitting sand swage on turnbuckles at lower fittings

MAINSAIL 8.0oz Cruising cross cut main with three reefs and a total area of 35.23m2

HEADSAIL 8.0oz Cruising cross cut,80% hanks on Yankee-total area of 45.93m2

STAYSAIL 8.0oz Cruising cross cut hanks on Staysail-total area of 19.36m2

BOOM COVER

YANKEE 

READY BAG

STAYSAIL

READY BAG

Stainless Steel Pulpit
Stainless Steel Boomkin
Bronze Port Holes
6 custom bronze mooring cleat/fairlead combination
2 large bronze freeing ports
Bronze labeled water and fuel deck fillers
2 custom bronze hawse pipes
Custom bronze double anchor rollers

Primaries 2 x #502 speed Bronze Self Tailing Winches
Staysail 1 x #162 speed Bronze Self Tailing Winch
Mainsheet1 x #442 speed Bronze Self Tailing Winch
Halyards 3 x #302 speed Bronze Self Tailing Winches
Outhaul1 x #162 speed Bronze Self Tailing Winch
Reefing1 x #162 speed Bronze Self Tailing Winch

Item Cast & Machined Bronze Components

1 ANCHOR ROLLERS

(2) 2 WHISKER STAY FITTING

3 BOWSPRIT STAR

4 COMPRESSION POST TOP FITTING

5 COMPRESSION POST BASE LOWER FITTING

6 COMPRESSION POST - BRASS TUBE MACHINED ONE END (with s/s fabricated compression adjuster)

7 SCUPPER DRAINS (ANGLED TYPE FOR C/PIT SEATS) (4)

8 GENOA CARS (Genoa x 4 / Staysail x 2) (6)

9 TABLE BASE PLATE

10 HAWSE PIPE FAIRLEADS WITH HORNS - (STRAIGHT) (6)

11 HAWSE PIPE FAIRLEADS BACKING RINGS (6)

12 BOOM GALLOWS BASE (2)

13 BOOM GALLOWS ARMS (2)

14 PORTLIGHT - OVAL - WITH SAFETY GLASS, SCREEN AND OUTER TRIM RING

15 PORTLIGHT - ROUND - WITH SAFETY GLASS, SCREEN, OUTER TRIM RING and DRAIN HOLE

16 MAINSHEET TRACK ARCH

17 MAINSHEET TRACK ARCH UPSTANDS (2)

18 FREEING PORTS (LARGE ) (2)

19 SKYLIGHT HINGES (LARGE) (3)

20 RUDDER HEEL FITTING

21 RUDDER GUDGEON (PAIR)

22 SAMPSON POST CAPS (Largest size)

23 ANCHOR CHAIN WELLS (2)

24 COWL VENTS (2)

25 DORADE BOX ACCESS PORTS (2) + (4)

26 CUSTOM FORWARD BRONZE HATCHES

(2) Item Cast & Machined Aluminum Components

1 STEERING RADIAL DRIVE ASSEMBLY (machined to fit rudder stock)

2 TABLE SUPPORT (for underneath plywood / wood table top - painted white)

Item Cast & Machined Stainless Steel Components

1 Cranz Iron

2 Gammon Band

3 Stanchion Bases (each one different angles to suit different angles of bulwarks)

4 Mast Base Plate

5 Bob Stay Assembly

6 Full Bow Sprit with base and guardrails

7 Full Push Sprit with base and guardrails

8 Stern Fitting

9 Rudder Shaft

10 Chain Plates (6)

Item Custom Wood Components Manufactured and in Storage

1 Forward workshop louvered door with split frame

2 Forward berth louvered door with split frame

3 Quarter berth hinged louvered door with split frame

4 Head louvered door with split frame

5 Under Pullman storage dresser with drawers and doors

6 Custom Staving (2" x 7/32") for all vertical surfaces (361 Sq Ft)

Item Aftermarket Components in Storage

P-00001 Fynspray Galley Pump (Fresh)

P-00002 Fynspray Galley Pump (Salt)

P-00003 Fynspray Service Kit

P-00004 Kitchen Bridge Faucet (Brass)

P-00005 Bathroom Bridge Faucet (Brass)

P-00006 Isotemp Water Heater

P-00007 Bronze Hose Deck Fill - Water

P-00008 Bronze Hose Deck Fill - Waste

P-00009 Bronze Hose Deck Fill - Diesel

P-00010A Deck Fill Replacement Cap

P-00010B Deck Fill Replacement Key

P-00010C Deck Fill Replacement O Ring

P-00011 Dynaplate Super Grounding Plate

P-00019 Splendide Washer & Dryer

P-000XX Groco PST-2 Storage Tank

P-000XX Bronze Hereshoff Cleats (4)

P-000XX Two Aluminum Trident Propane Tanks

Item Custom Components Manufactured and in Storage

A Aquadrive thurst bearing with machined adapter plates for angled transmission

B Blue Sea AC/DC Electrical Distribution Panel

C Fiberglass Bowsprit

D Cutlass Bearing and Housing

Item Miscellaneous

A Custom Steel Cradle for Boat

B Custom Steel Stairs with 11.5' Platform

The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.